-
1 conducteur (isolé)
изолированная жила (термин употребляется в Северной Америке)
совокупность элементов, состоящая из жилы, ее изоляции (и экранов, если они есть)
Примечание. В Северной Америке термин «core of a cable» определяется как совокупность компонентов кабеля, расположенных под общим защитным покровом, таким как оболочка. Такое применение этого термина не допустимо
[IEV number 461-04-04]EN
core
insulated conductor
assembly comprising a conductor with its own insulation (and screens if any)
NOTE – In North American usage, the core of a cable has been defined as the assembly of components of a cable lying under a common covering such as the sheath. Such usage is deprecated.
[IEV number 461-04-04]FR
conducteur (isolé)
ensemble comprenant l'âme, son enveloppe isolante et ses écrans éventuels
NOTE – En Amérique du Nord le terme “core of a cable” a été défini comme l'ensemble des constituants d'un câble disposés sous un revêtement commun, tel que la gaine. L'utilisation de ce terme est déconseillée dans ce sens.
[IEV number 461-04-04]Тематики
- кабели, провода...
EN
DE
- Ader, f
FR
изолированный провод
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]EN
core insulated conductor
assembly comprising a conductor and its own insulation (and screens, if any)
[IEC 61892-4, ed. 1.0 (2007-06)]
core-insulated conductor (North America)
assembly comprising a conductor and its own insulation (and screens, if any)
NOTE In North American usage, the core of a cable has been defined as the assembly of components of a cable lying under a common covering such as the sheath (jacket).
[IEC 60092-350, ed. 3.0 (2008-02)]FR
conducteur (isolé)
ensemble comprenant l'âme, son enveloppe isolante et ses écrans éventuels
Note – En Amérique du Nord le terme “core of a cable” a été défini comme l'ensemble des constituants d'un câble disposés sous un revêtement commun, tel que la gaine. L'utilisation de ce terme est déconseillée dans ce sens.
[ IEV ref 461-04-04]Рис. Schneider Electric
Параллельные тексты EN-RU
An insulated conductor is made up of a conductor core and its
insulating envelope.
[Schneider Electric]Изолированный провод состоит из токопроводящей жилы и изоляции провода.
[Перевод Интент]Тематики
- кабели, провода...
EN
- core insulated conductor
- core-insulated conductor
- covered conductor
- covered wire
- insulated conductor
DE
- Ader, f
FR
Франко-русский словарь нормативно-технической терминологии > conducteur (isolé)
-
2 courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant admissible, m
-
3 courant permanent admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant permanent admissible, m
-
4 tension assignée
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
Франко-русский словарь нормативно-технической терминологии > tension assignée
-
5 tension nominale
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
номинальное напряжение конденсатора
Максимальное напряжение, при котором конденсатор может работать в течение минимальной наработки в условиях, указанных в нормативно-технической документации
[ ГОСТ 21415-75]
номинальное напряжение конденсатора
Действующее значение синусоидального переменного напряжения при номинальной частоте, на которое рассчитан конденсатор. Номинальное напряжение многофазного конденсатора - значение напряжения между выводами.
[ ГОСТ 1282-88]Тематики
- конденсаторы для повыш. коэф. мощности
- конденсаторы для электронной аппаратуры
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > tension nominale
-
6 Un
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
Франко-русский словарь нормативно-технической терминологии > Un
-
7 transformateur de courant à circuit magnétique ouvrant
разъемный трансформатор тока
Трансформатор тока без первичной обмотки, магнитная цепь которого может размыкаться и затем замыкаться вокруг проводника с измеряемым током.
[ ГОСТ 18685-73]EN
split core type current transformer
a current transformer without primary conductor, and primary insulation of its own, the magnetic circuit of which can be hinged open (or otherwise separated into two parts) and then closed around the insulated conductor carrying the current to be measured
[IEV number 321-02-05]FR
transformateur de courant à circuit magnétique ouvrant
transformateur de courant sans enroulement primaire et sans isolation propre dont le circuit magnétique peut être ouvert puis refermé autour d'un conducteur isolé parcouru par le courant à mesurer
[IEV number 321-02-05]
[http://www.rusotools.ru/offers/8774/разъемный-трансформатор-тока-тзрл-125-у3.html]
Трансформатор выполнен в виде опорной разъемной конструкции. Роль первичной обмотки выполняет трехфазный кабель на напряжение до 10 кВ, пропущенный в окно трансформатора. Вторичная обмотка намотана на тороидальный магнитопровод, разрезанный пополам. Обе части, залитые изоляционным компаундом на основе эпоксидной смолы, соединяются болтами. Опорой трансформатора служит основание изоляционного корпуса со специальными втулками для крепления[http://www.laborant.ru/eltech/02/4/1/27-99.htm]
Недопустимые, нерекомендуемые
- разборный трансформатор
- расчленяемый трансформатор тока
- трансформатор тока с раздельным сердечником
- трансформатор тока с расчленяемым сердечником
Тематики
Классификация
>>>Синонимы
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > transformateur de courant à circuit magnétique ouvrant
-
8 fil pilote
контрольная жила
Вспомогательная жила, служащая для целей контроля и сигнализации и входящая в состав токопроводящей жилы силового кабеля.
[ ГОСТ 15845-80]
контрольная жила
изолированная токопроводящая жила, входящая о состав силового кабеля и предназначенная для передачи сигналов
[IEV number 461-04-08]EN
pilot core
pilot wire (deprecated in this sense)
insulated conductor incorporated in a power cable assembly and designed for the transmission of signals
IEV number 461-04-08]FR
fil pilote
conducteur isolé incorporé à l’assemblage d’un câble d’énergie et destiné à la transmission de signaux
[IEV number 461-04-08]Тематики
- кабели, провода...
EN
DE
- Prüfader, f
- Steuerader, f
FR
Франко-русский словарь нормативно-технической терминологии > fil pilote
-
9 traversée
ввод
Проходной изолятор, имеющий внутреннюю изоляцию из жидкого, твердого, газообразного диэлектрического материала или их комбинации.
[ ГОСТ 27744-88 ]EN
bushing
device that enables one or several conductors to pass through a partition such as a wall or a tank, and insulate the conductors from it.
NOTE 1 – The means of attachment (flange or fixing device) to the partition forms part of the bushing. The conductor may form an integral part of the bushing or be drawn into the central tube of the bushing.
NOTE 2 – The bushings may be of the following types:
- liquid-filled bushing;
- liquid-insulated bushing;
- gas-filled bushing;
- gas-insulated bushing;
- oil-impregnated paper bushing;
- resin-bonded paper bushing;
- resin-impregnated paper bushing;
- ceramic, glass or analogous inorganic material bushing;
- cast or moulded resin-insulated bushing;
- combined insulation bushing;
- compound-filled bushing;
- gas-impregnated bushing.
[IEV number 471-02-01]FR
traversée
dispositif servant à faire passer un ou plusieurs conducteurs à travers une paroi, telle qu’un mur ou une cuve, en isolant le(s) conducteur(s) de cette paroi.
NOTE 1 – Les moyens de fixation (bride ou autre dispositif) sur la paroi font partie de la traversée. Le conducteur peut être solidaire de la traversée ou démontable.
NOTE 2 – Les différentes traversées peuvent être les suivantes:
- traversée à remplissage d’un liquide;
- traversée à isolation liquide;
- traversée à remplissage de gaz;
- traversée à isolation gazeuse;
- traversée en papier imprégné d’huile;
- traversée en papier enduit de résine;
- traversée en papier imprégné de résine;
- traversée en matière céramique, en verre ou en matière inorganique analogue;
- traversée à isolation en résine coulée ou moulée;
- traversée à isolation combinée;
- traversée à remplissage de mélange;
- traversée imprégnée de gaz.
[IEV number 471-02-01]Тематики
EN
DE
- Durchführung, f
FR
проходной изолятор
Изолятор, предназначенный для провода токоведущих элементов через стенку, имеющую другой электрический потенциал.
[ ГОСТ 27744-88]
проходной изолятор
-
[IEV number 151-15-40]EN
(insulating) bushing
insulator forming a passage for a conductor through a non-insulating partition
[IEV number 151-15-40]
bushing
A bushing is a cyclindrical insulating component, usually made of ceramic, that houses a conductor. It enables a conductor to pass through a grounded enclosure, such as a transformer tank (the physical shell of a transformer), a wall or other physical barrier, to connect electrical installations. In the case of a transformer, bushings protect the conductors that connect a transformer’s core to the power system it serves through channels in the transformer’s housing.
[ABB. Glossary of technical terms. 2010]FR
isolateur de traversée, m
traversée, f
isolateur permettant le passage d'un conducteur à travers une paroi non isolante
[IEV number 151-15-40]
Проходной изоляторПараллельные тексты EN-RU
The circuit breaker is connected via bushings to the rest of the switchgear at the flanges provided.
[Siemens]С другими частями распределительного устройства силовой выключатель соединяется через проходные изоляторы, закрепленные в его фланцах.
[Перевод Интент]Тематики
Классификация
>>>Обобщающие термины
EN
DE
FR
- isolateur de traversée, m
- traversée
Франко-русский словарь нормативно-технической терминологии > traversée
-
10 cable de garde
грозозащитный трос
Проводник, заземленный непосредственно или через искровые промежутки, расположенный над фазными проводами воздушной линии электропередачи или подстанции и предназначенный для защиты их от поражений молнией.
[ ГОСТ 24291-90]EN
overhead earth wire
overhead ground wire (US)
conductor intentionally earthed at some or all supports of an overhead line, which is generally but not necessarily installed above the line conductors
Source: 466-10-25 MOD, 604-03-48 MOD
[IEV number 195-02-26]
overhead earth wire
ground-wire (US)
a conductor connected to earth or lightly insulated, usually installed above the phase conductors of a line or a substation to protect them from lightning strikes
[IEV number 604-03-48]
earth wire
shield wire
overhead ground wire (US)
a conductor connected to earth at some or all supports, which is suspended usually but not necessarily above the line conductors to provide a degree of protection against lightning strokes
[IEV number 466-10-25]FR
câble de garde
conducteur intentionnellement mis à la terre à certains ou à tous les supports d'une ligne aérienne, généralement mais non nécessairement disposé au-dessus des conducteurs de ligne
Source: 466-10-25 MOD, 604-03-48 MOD
[IEV number 195-02-26]
câble de garde
conducteur mis à la terre ou faiblement isolé et disposé au dessus des conducteurs de phase d'une ligne ou d'un poste, de façon à les protéger des coups de foudre
[IEV number 604-03-48]
câble de garde
conducteur mis à la terre à certains ou à tous les supports, disposé généralement mais non nécessairement au-dessus des conducteurs de phase pour assurer une certaine protection contre les coups de foudre
[IEV number 466-10-25]Тематики
EN
DE
FR
заземляющий провод воздушной линии
Проводник, преднамеренно заземленный на части опор или всех опорах воздушной линии, как правило, но не обязательно расположенный выше линейных проводников.
[ ГОСТ Р МЭК 60050-195-2005]EN
overhead earth wire
conductor intentionally earthed at some or all supports of an overhead line, which is generally but not necessarily installed above the line conductors
Source: 466-10-25 MOD, 604-03-48 MOD
[IEV number 195-02-26]FR
câble de garde
conducteur intentionnellement mis à la terre à certains ou à tous les supports d'une ligne aérienne, généralement mais non nécessairement disposé au-dessus des conducteurs de ligne
Source: 466-10-25 MOD, 604-03-48 MOD
[IEV number 195-02-26]Тематики
EN
DE
FR
Проводник, заземленный непосредственно или через искровые промежутки, расположенный над фазными проводами воздушной линии электропередачи или подстанции и предназначенный для защиты их от повреждений молнией
604-03-48*
de Erdseil
en overhead earth wire ground-wire (USA)
fr câble de garde
Источник: ГОСТ 24291-90: Электрическая часть электростанции и электрической сети. Термины и определения оригинал документа
Франко-русский словарь нормативно-технической терминологии > cable de garde
-
11 âme concentrique
концентрическая токопроводящая жила
токопроводящая жила, окружающая одну или несколько изолированных жил
[IEV number 461-01-17]EN
concentric conductor
conductor so constructed as to surround one or more insulated conductors
[IEV number 461-01-17]FR
âme concentrique
âme réalisée de façon à entourer un ou plusieurs conducteurs isolés
[IEV number 461-01-17]
Тематики
- кабели, провода...
EN
DE
- konzentrischer Leiter, m
FR
Франко-русский словарь нормативно-технической терминологии > âme concentrique
-
12 câble unipolaire
одножильный кабель
кабель, имеющий только одну изолированную жилу
Примечание. Французский термин «cable unipolaire» более приемлем для обозначения кабеля, составляющего одну из фаз многофазной системы
[ IEV ref 461-06-02]EN
single-conductor cable
single-core cable
cable having only one core
Note – The French term «câble unipolaire» is more specifically used to designate the cable constituting one of the phases of a multiphase system.
[ IEV ref 461-06-02]FR
câble à un conducteur
câble unipolaire
câble comprenant un seul conducteur isolé
Note – Le terme câble unipolaire est plus particulièrement utilisé pour désigner le câble constituant l'une des phases d'un système polyphasé.
[ IEV ref 461-06-02]Параллельные тексты EN-RU
The cables must be multi strand, single core and PVC insulated.
[Schneider Electric]Должны применяться одножильные кабели с многопроволочной жилой с ПВХ изоляцией.
[Перевод Интент]
Рис. Schneider Electric
Core - (токопроводящая) жила;
Insulator - изоляция жилы;
Protective Sheath - оболочка кабеля.Тематики
- кабели, провода...
EN
- monoconductor cable
- single cable
- single conductor cable
- single core cable
- single-conductor cable
- single-core cable
- single-pole cable
DE
- einadriges Kabel, n
- Einleiterkabel, n
FR
Франко-русский словарь нормативно-технической терминологии > câble unipolaire
13 câble à un conducteur
одножильный кабель
кабель, имеющий только одну изолированную жилу
Примечание. Французский термин «cable unipolaire» более приемлем для обозначения кабеля, составляющего одну из фаз многофазной системы
[ IEV ref 461-06-02]EN
single-conductor cable
single-core cable
cable having only one core
Note – The French term «câble unipolaire» is more specifically used to designate the cable constituting one of the phases of a multiphase system.
[ IEV ref 461-06-02]FR
câble à un conducteur
câble unipolaire
câble comprenant un seul conducteur isolé
Note – Le terme câble unipolaire est plus particulièrement utilisé pour désigner le câble constituant l'une des phases d'un système polyphasé.
[ IEV ref 461-06-02]Параллельные тексты EN-RU
The cables must be multi strand, single core and PVC insulated.
[Schneider Electric]Должны применяться одножильные кабели с многопроволочной жилой с ПВХ изоляцией.
[Перевод Интент]
Рис. Schneider Electric
Core - (токопроводящая) жила;
Insulator - изоляция жилы;
Protective Sheath - оболочка кабеля.Тематики
- кабели, провода...
EN
- monoconductor cable
- single cable
- single conductor cable
- single core cable
- single-conductor cable
- single-core cable
- single-pole cable
DE
- einadriges Kabel, n
- Einleiterkabel, n
FR
Франко-русский словарь нормативно-технической терминологии > câble à un conducteur
14 âme segmentée
расщепленная токопроводящая жила
скрученная токопроводящая жила, состоящая из ряда скрученных фасонных токопроводящих жил, имеющих незначительную изоляцию друг от друга
[IEV number 461-01-15]EN
Milliken conductor
stranded conductor comprising an assembly of shaped stranded conductors, lightly insulated from each other
[IEV number 461-01-15]FR
âme segmentée
âme câblée composée d'éléments toronnés profilés, faiblement isolés les uns par rapport aux autres
[IEV number 461-01-15]
Тематики
- кабели, провода...
EN
DE
- Millikenleiter, m
- Segmentleiter, m
FR
Франко-русский словарь нормативно-технической терминологии > âme segmentée
15 connexion enroulée renforcée
модифицированная накрутка
Накрутка, выполняемая таким образом, что с несколькими виками оголенного провода накручиваются 2-3 витка изолированного провода. Такая накрутка более устойчива к воздействию вибрации.
[В. Ф. Лярский, О. Б. Мурадян. Электрические соединители. Справочник. Радио и связь, 1988]EN
modified wrapped connection
wrapped connection achieved by wrapping an insulated solid conductor around a wrap post in such a way that the insulation of the conductor covers the outer sides of wrap at at least three corners of the wrap post
[IEV number 581-23-36]FR
connexion enroulée renforcée
connexion enroulée obtenue par enroulement d'un conducteur isolé massif autour d'une borne pour connexion enroulée de manière à ce que l'isolant du fil soit en contact avec au moins trois arêtes de la borne pour connexion enroulée
[IEV number 581-23-36]
а) обычная накрутка; б) - модифицированная накрутка
[В. Ф. Лярский, О. Б. Мурадян. Электрические соединители. Справочник. Радио и связь, 1988]Тематики
EN
DE
- modifizierte Wickelverbindung, f
FR
Смотри также
Франко-русский словарь нормативно-технической терминологии > connexion enroulée renforcée
16 connexion enroulée simple
обычная накрутка
Накрутка, выполняемая только витками оголенного провода без накручивания витков изолированного провода.
[Интент]EN
conventional wrapped connection
wrapped connection achieved by wrapping an insulated solid conductor around a wrap post in such a way that the insulation of the conductor does not cover the wrap post anywhere
[IEV number 581-23-37]FR
connexion enroulée simple
connexion enroulée obtenue par enroulement d'un conducteur isolé massif autour d'une borne pour connexion enroulée de manière à ce que l'isolant du fil ne soit nulle part en contact avec la borne pour connexion enroulée
[IEV number 581-23-37]
а) обычная накрутка; б) - модифицированная накрутка
[В. Ф. Лярский, О. Б. Мурадян. Электрические соединители. Справочник. Радио и связь, 1988]Тематики
EN
DE
- konventionelle Wickelverbindung, f
FR
Смотри также
Франко-русский словарь нормативно-технической терминологии > connexion enroulée simple
17 ligne aérienne
воздушная линия электропередачи
ВЛ
Линия электропередачи, провода которой поддерживаются над землей с помощью опор, изоляторов.
[ ГОСТ 24291-90]
воздушная линия электропередачи
Устройство для передачи электроэнергии по проводам, расположенным на открытом воздухе и прикрепленным с помощью изоляторов и арматуры к опорам или кронштейнам и стойкам на инженерных сооружениях (мостах, путепроводах и т. п.). За начало и конец воздушной линии электропередачи принимаются линейные порталы или линейные вводы распределительного устройства (далее - РУ), а для ответвлений - ответвительная опора и линейный портал или линейный ввод РУ.
[Правила технической эксплуатации электроустановок потребителей. Министерство энергетики РФ. 2003 г.]
линия электропередачи воздушная
Линия электропередачи, расположенная на открытом воздухе, провод которой прикреплён к опорам при помощи изоляторов и арматуры
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]
воздушная линия электропередачи
Устройство для передачи электроэнергии по проводам, расположенным на открытом воздухе и прикрепленным с помощью изоляторов и арматуры к опорам или кронштейнам и стойкам на инженерных сооружениях (мостах, путепроводах и т.п.). За начало и конец воздушной линии электропередачи принимаются линейные порталы или линейные вводы РУ, а для ответвлений - ответвительная опора и линейный портал или линейный ввод РУ.
[ПОТ Р М-016-2001]
[РД 153-34.0-03.150-00]
воздушные линии электропередачи
ВЛ
ВЛЭП
Конструкции для передачи электроэнергии на расстояние по проводам. Основными конструктивными элементами ВЛ являются провода, тросы, опоры, изоляторы и линейная арматура. Провода служат для передачи электроэнергии. В верхней части опор над проводами для защиты ВЛ от грозовых перенапряжений монтируют грозозащитные тросы. Опоры поддерживают провода и тросы на определенной высоте над уровнем земли или воды. Изоляторы изолируют провода от опоры. С помощью линейной арматуры провода закрепляются на изоляторах, а изоляторы на опорах. В некоторых случаях провода ВЛ с помощью изоляторов и линейной арматуры прикрепляются к кронштейнам инженерных сооружений.
[ http://www.energo-konsultant.ru/termini]
воздушная линия
-
[IEV number 151-12-33]EN
overhead line
line with one or more conductors or a cable supported above ground by appropriate means
NOTE 1 – An overhead line may consist of only one conductor when the circuit is closed by the Earth.
NOTE 2 – An overhead line may be constructed with bare conductors, generally supported by insulators, or with insulated conductors.
NOTE 3 – The concept of overhead line generally includes the supporting elements.
Source: 466-01-02 MOD, 601-03-04 MOD
[IEV number 151-12-33]
overhead power line
Suspended cables by which electrical power is distributed throughout a country. (Source: UVAROVa)
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]FR
ligne aérienne, f
ligne comportant un ou plusieurs conducteurs ou un câble maintenus au-dessus du sol par des supports appropriés
NOTE 1 – Une ligne aérienne peut être formée d’un seul conducteur lorsque le circuit est fermé par la Terre.
NOTE 2 – Une ligne aérienne peut être constituée de conducteurs nus, généralement maintenus au moyen d’isolateurs, ou de conducteurs avec isolation.
NOTE 3 – Le concept de ligne aérienne inclut généralement les supports.
Source: 466-01-02 MOD, 601-03-04 MOD
[IEV number 151-12-33]В сельской местности, в малых городах и поселках потребители получают питание в основном по воздушным ЛЭП.
[Макаров Е.Ф. Справочник по электрическим сетям 0,4-35 кВ и 110-1150 кВ]Тематики
Синонимы
EN
- aerial power line
- overhead line
- overhead network
- overhead power line
- overhead power transmission line
DE
FR
51 воздушная линия электропередачи; ВЛ
Линия электропередачи, провода которой поддерживаются над землей с помощью опор, изоляторов
601-03-04
de Freileitung
en overhead line
fr ligne aérienne
Источник: ГОСТ 24291-90: Электрическая часть электростанции и электрической сети. Термины и определения оригинал документа
35. Воздушная линия электропередачи
ВЛ
E. Overhead line
F. Ligne aérienne
Источник: ГОСТ 19431-84: Энергетика и электрификация. Термины и определения оригинал документа
Франко-русский словарь нормативно-технической терминологии > ligne aérienne
18 ligne aérienne de transport d'énergie
воздушная линия электропередачи
ВЛ
Линия электропередачи, провода которой поддерживаются над землей с помощью опор, изоляторов.
[ ГОСТ 24291-90]
воздушная линия электропередачи
Устройство для передачи электроэнергии по проводам, расположенным на открытом воздухе и прикрепленным с помощью изоляторов и арматуры к опорам или кронштейнам и стойкам на инженерных сооружениях (мостах, путепроводах и т. п.). За начало и конец воздушной линии электропередачи принимаются линейные порталы или линейные вводы распределительного устройства (далее - РУ), а для ответвлений - ответвительная опора и линейный портал или линейный ввод РУ.
[Правила технической эксплуатации электроустановок потребителей. Министерство энергетики РФ. 2003 г.]
линия электропередачи воздушная
Линия электропередачи, расположенная на открытом воздухе, провод которой прикреплён к опорам при помощи изоляторов и арматуры
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]
воздушная линия электропередачи
Устройство для передачи электроэнергии по проводам, расположенным на открытом воздухе и прикрепленным с помощью изоляторов и арматуры к опорам или кронштейнам и стойкам на инженерных сооружениях (мостах, путепроводах и т.п.). За начало и конец воздушной линии электропередачи принимаются линейные порталы или линейные вводы РУ, а для ответвлений - ответвительная опора и линейный портал или линейный ввод РУ.
[ПОТ Р М-016-2001]
[РД 153-34.0-03.150-00]
воздушные линии электропередачи
ВЛ
ВЛЭП
Конструкции для передачи электроэнергии на расстояние по проводам. Основными конструктивными элементами ВЛ являются провода, тросы, опоры, изоляторы и линейная арматура. Провода служат для передачи электроэнергии. В верхней части опор над проводами для защиты ВЛ от грозовых перенапряжений монтируют грозозащитные тросы. Опоры поддерживают провода и тросы на определенной высоте над уровнем земли или воды. Изоляторы изолируют провода от опоры. С помощью линейной арматуры провода закрепляются на изоляторах, а изоляторы на опорах. В некоторых случаях провода ВЛ с помощью изоляторов и линейной арматуры прикрепляются к кронштейнам инженерных сооружений.
[ http://www.energo-konsultant.ru/termini]
воздушная линия
-
[IEV number 151-12-33]EN
overhead line
line with one or more conductors or a cable supported above ground by appropriate means
NOTE 1 – An overhead line may consist of only one conductor when the circuit is closed by the Earth.
NOTE 2 – An overhead line may be constructed with bare conductors, generally supported by insulators, or with insulated conductors.
NOTE 3 – The concept of overhead line generally includes the supporting elements.
Source: 466-01-02 MOD, 601-03-04 MOD
[IEV number 151-12-33]
overhead power line
Suspended cables by which electrical power is distributed throughout a country. (Source: UVAROVa)
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]FR
ligne aérienne, f
ligne comportant un ou plusieurs conducteurs ou un câble maintenus au-dessus du sol par des supports appropriés
NOTE 1 – Une ligne aérienne peut être formée d’un seul conducteur lorsque le circuit est fermé par la Terre.
NOTE 2 – Une ligne aérienne peut être constituée de conducteurs nus, généralement maintenus au moyen d’isolateurs, ou de conducteurs avec isolation.
NOTE 3 – Le concept de ligne aérienne inclut généralement les supports.
Source: 466-01-02 MOD, 601-03-04 MOD
[IEV number 151-12-33]В сельской местности, в малых городах и поселках потребители получают питание в основном по воздушным ЛЭП.
[Макаров Е.Ф. Справочник по электрическим сетям 0,4-35 кВ и 110-1150 кВ]Тематики
Синонимы
EN
- aerial power line
- overhead line
- overhead network
- overhead power line
- overhead power transmission line
DE
FR
Франко-русский словарь нормативно-технической терминологии > ligne aérienne de transport d'énergie
19 ligne de transmission électrique aérienne
воздушная линия электропередачи
ВЛ
Линия электропередачи, провода которой поддерживаются над землей с помощью опор, изоляторов.
[ ГОСТ 24291-90]
воздушная линия электропередачи
Устройство для передачи электроэнергии по проводам, расположенным на открытом воздухе и прикрепленным с помощью изоляторов и арматуры к опорам или кронштейнам и стойкам на инженерных сооружениях (мостах, путепроводах и т. п.). За начало и конец воздушной линии электропередачи принимаются линейные порталы или линейные вводы распределительного устройства (далее - РУ), а для ответвлений - ответвительная опора и линейный портал или линейный ввод РУ.
[Правила технической эксплуатации электроустановок потребителей. Министерство энергетики РФ. 2003 г.]
линия электропередачи воздушная
Линия электропередачи, расположенная на открытом воздухе, провод которой прикреплён к опорам при помощи изоляторов и арматуры
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]
воздушная линия электропередачи
Устройство для передачи электроэнергии по проводам, расположенным на открытом воздухе и прикрепленным с помощью изоляторов и арматуры к опорам или кронштейнам и стойкам на инженерных сооружениях (мостах, путепроводах и т.п.). За начало и конец воздушной линии электропередачи принимаются линейные порталы или линейные вводы РУ, а для ответвлений - ответвительная опора и линейный портал или линейный ввод РУ.
[ПОТ Р М-016-2001]
[РД 153-34.0-03.150-00]
воздушные линии электропередачи
ВЛ
ВЛЭП
Конструкции для передачи электроэнергии на расстояние по проводам. Основными конструктивными элементами ВЛ являются провода, тросы, опоры, изоляторы и линейная арматура. Провода служат для передачи электроэнергии. В верхней части опор над проводами для защиты ВЛ от грозовых перенапряжений монтируют грозозащитные тросы. Опоры поддерживают провода и тросы на определенной высоте над уровнем земли или воды. Изоляторы изолируют провода от опоры. С помощью линейной арматуры провода закрепляются на изоляторах, а изоляторы на опорах. В некоторых случаях провода ВЛ с помощью изоляторов и линейной арматуры прикрепляются к кронштейнам инженерных сооружений.
[ http://www.energo-konsultant.ru/termini]
воздушная линия
-
[IEV number 151-12-33]EN
overhead line
line with one or more conductors or a cable supported above ground by appropriate means
NOTE 1 – An overhead line may consist of only one conductor when the circuit is closed by the Earth.
NOTE 2 – An overhead line may be constructed with bare conductors, generally supported by insulators, or with insulated conductors.
NOTE 3 – The concept of overhead line generally includes the supporting elements.
Source: 466-01-02 MOD, 601-03-04 MOD
[IEV number 151-12-33]
overhead power line
Suspended cables by which electrical power is distributed throughout a country. (Source: UVAROVa)
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]FR
ligne aérienne, f
ligne comportant un ou plusieurs conducteurs ou un câble maintenus au-dessus du sol par des supports appropriés
NOTE 1 – Une ligne aérienne peut être formée d’un seul conducteur lorsque le circuit est fermé par la Terre.
NOTE 2 – Une ligne aérienne peut être constituée de conducteurs nus, généralement maintenus au moyen d’isolateurs, ou de conducteurs avec isolation.
NOTE 3 – Le concept de ligne aérienne inclut généralement les supports.
Source: 466-01-02 MOD, 601-03-04 MOD
[IEV number 151-12-33]В сельской местности, в малых городах и поселках потребители получают питание в основном по воздушным ЛЭП.
[Макаров Е.Ф. Справочник по электрическим сетям 0,4-35 кВ и 110-1150 кВ]Тематики
Синонимы
EN
- aerial power line
- overhead line
- overhead network
- overhead power line
- overhead power transmission line
DE
FR
Франко-русский словарь нормативно-технической терминологии > ligne de transmission électrique aérienne
20 ligne électrique aérienne
воздушная линия электропередачи
ВЛ
Линия электропередачи, провода которой поддерживаются над землей с помощью опор, изоляторов.
[ ГОСТ 24291-90]
воздушная линия электропередачи
Устройство для передачи электроэнергии по проводам, расположенным на открытом воздухе и прикрепленным с помощью изоляторов и арматуры к опорам или кронштейнам и стойкам на инженерных сооружениях (мостах, путепроводах и т. п.). За начало и конец воздушной линии электропередачи принимаются линейные порталы или линейные вводы распределительного устройства (далее - РУ), а для ответвлений - ответвительная опора и линейный портал или линейный ввод РУ.
[Правила технической эксплуатации электроустановок потребителей. Министерство энергетики РФ. 2003 г.]
линия электропередачи воздушная
Линия электропередачи, расположенная на открытом воздухе, провод которой прикреплён к опорам при помощи изоляторов и арматуры
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]
воздушная линия электропередачи
Устройство для передачи электроэнергии по проводам, расположенным на открытом воздухе и прикрепленным с помощью изоляторов и арматуры к опорам или кронштейнам и стойкам на инженерных сооружениях (мостах, путепроводах и т.п.). За начало и конец воздушной линии электропередачи принимаются линейные порталы или линейные вводы РУ, а для ответвлений - ответвительная опора и линейный портал или линейный ввод РУ.
[ПОТ Р М-016-2001]
[РД 153-34.0-03.150-00]
воздушные линии электропередачи
ВЛ
ВЛЭП
Конструкции для передачи электроэнергии на расстояние по проводам. Основными конструктивными элементами ВЛ являются провода, тросы, опоры, изоляторы и линейная арматура. Провода служат для передачи электроэнергии. В верхней части опор над проводами для защиты ВЛ от грозовых перенапряжений монтируют грозозащитные тросы. Опоры поддерживают провода и тросы на определенной высоте над уровнем земли или воды. Изоляторы изолируют провода от опоры. С помощью линейной арматуры провода закрепляются на изоляторах, а изоляторы на опорах. В некоторых случаях провода ВЛ с помощью изоляторов и линейной арматуры прикрепляются к кронштейнам инженерных сооружений.
[ http://www.energo-konsultant.ru/termini]
воздушная линия
-
[IEV number 151-12-33]EN
overhead line
line with one or more conductors or a cable supported above ground by appropriate means
NOTE 1 – An overhead line may consist of only one conductor when the circuit is closed by the Earth.
NOTE 2 – An overhead line may be constructed with bare conductors, generally supported by insulators, or with insulated conductors.
NOTE 3 – The concept of overhead line generally includes the supporting elements.
Source: 466-01-02 MOD, 601-03-04 MOD
[IEV number 151-12-33]
overhead power line
Suspended cables by which electrical power is distributed throughout a country. (Source: UVAROVa)
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]FR
ligne aérienne, f
ligne comportant un ou plusieurs conducteurs ou un câble maintenus au-dessus du sol par des supports appropriés
NOTE 1 – Une ligne aérienne peut être formée d’un seul conducteur lorsque le circuit est fermé par la Terre.
NOTE 2 – Une ligne aérienne peut être constituée de conducteurs nus, généralement maintenus au moyen d’isolateurs, ou de conducteurs avec isolation.
NOTE 3 – Le concept de ligne aérienne inclut généralement les supports.
Source: 466-01-02 MOD, 601-03-04 MOD
[IEV number 151-12-33]В сельской местности, в малых городах и поселках потребители получают питание в основном по воздушным ЛЭП.
[Макаров Е.Ф. Справочник по электрическим сетям 0,4-35 кВ и 110-1150 кВ]Тематики
Синонимы
EN
- aerial power line
- overhead line
- overhead network
- overhead power line
- overhead power transmission line
DE
FR
Франко-русский словарь нормативно-технической терминологии > ligne électrique aérienne
Страницы- 1
- 2
См. также в других словарях:
Mineral-insulated copper-clad cable — MIMS redirects here. For multi isotope imaging mass spectrometry, see Isotope mass spectrometry. PVC sheathed MICC cable. Conductor cross section area is 1.5 mm²; overall diameter is 7.2 mm … Wikipedia
Electrical conductor — Overhead conductors carry electric power from generating stations to customers. In physics and electrical engineering, a conductor is a material which contains movable electric charges. In metallic conductors such as copper or aluminum, the… … Wikipedia
List of Tesla patents — Below is a list of Tesla patents. Dr. Nikola Tesla was an inventor who obtained around 300 patents [Snezana Sarbo, [http://www.tesla symp06.org/papers/Tesla Symp06 Sarboh.pdfNikola Tesla s Patents] , Sixth International Symposium Nikola Tesla,… … Wikipedia
изолированный провод — — [Я.Н.Лугинский, М.С.Фези Жилинская, Ю.С.Кабиров. Англо русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.] EN core insulated conductor assembly comprising a conductor and its own insulation (and screens, if any) [IEC… … Справочник технического переводчика
Power cable — This article is about electric power conductors. For portable equipment, see power cord. A power cable is an assembly of two or more electrical conductors, usually held together with an overall sheath. The assembly is used for transmission of… … Wikipedia
coaxial cable — noun a transmission line for high frequency signals • Syn: ↑coax, ↑coax cable • Derivationally related forms: ↑coax (for: ↑coax) • Hypernyms: ↑cable, ↑ … Useful english dictionary
длительный допустимый ток — (длительный) допустимый ток Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме … Справочник технического переводчика
Tesla coil — at Questacon the National Science and Technology center in Canberra, Australia Uses Application in educational demonstrations, novelty lighting, as well as music Inventor … Wikipedia
Ampacity — is the maximum amount of electrical current a conductor or device can carry before sustaining immediate or progressive deterioration. Also described as current rating or current carrying capacity, ampacity is the RMS electric current which a… … Wikipedia
изолированная жила (термин употребляется в Северной Америке) — совокупность элементов, состоящая из жилы, ее изоляции (и экранов, если они есть) Примечание. В Северной Америке термин «core of a cable» определяется как совокупность компонентов кабеля, расположенных под общим защитным покровом,… … Справочник технического переводчика
Electrothermal-chemical technology — Electrothermal chemical (ETC) technology is an attempt to increase accuracy and muzzle energy of future tank, artillery, and close in weapon system [cite book | first=Dr Norman|last=Friedman| coauthors=David K Brown, Eric Grove, Stuart Slade,… … Wikipedia
Перевод: с французского на русский
с русского на французский- С русского на:
- Французский
- С французского на:
- Русский